DIY: front bumper removal non m w/ pictures!

lsturbointeg · 10-22-2015, 01:49 AM

9 pages i went through and nothing with pictures! anybody have a link or did i just miss it? appreciate it guys!

Okay...decided to post a DIY with pictures for those of you who are contemplating doing it yourself.

1) "Pop the hood" as how our fallen brother Paul Walker said to Vin Diesel
2) locate the rubber seal just above where the bumper and Hood meet

3) Peel the rubber gasket completey off CAREFULLY

4) there are 4 of these pull/push type fasteners u need to remove. I used a small pliers but just pull the pin up like so and wiggle it as both parts should come up

5) next there are 4 T30 torx bolts that need to be removed

6) now next step would be to turn your wheel in depending on which side you're working first

7) there are 3 screws you will need to remove inside the fender wheel using a 5/16" socket

Bottom

Middle

Top right where the fender/bumper meet

8) here is where you'll need to go next...where the fender meets the front bumper. Doesn't matter which side you do first as they're both the same. As you can see I popped the fender liner open a bit

9) there are 2 more 5/16" screws to remove...the one all the way inside takes a bit or work as you really have to pull the fender well out and in a bit to get to. Up can see the screw next to my thumb

The 2nd one you can see way up inside

10) had to google these next images but next remove lower grills. Pull them with your fingers as they are just snapped in like so

11) remove the 2 5/16" screws

12) disconnect the fog lights from the harness by simply squeezing the tabs and pulling out. I put the fog lights in my trunk so I don't scratch the lens

13) last thing is to remove the 8 5/16" bolts underneath

14) now all you have to do carefully is wiggle the bumper off and that's it. Install is the same.

Hope that helps everyone as I searched all over the internet for DIY with pictures and came up empty

mragarg · 11-09-2015, 12:36 PM

Did you ever find it?

lsturbointeg · 11-09-2015, 12:47 PM

Quote:

Originally Posted by mragarg

Did you ever find it?

NO...but I could probably take some pictures and do a DIY?

mragarg · 11-09-2015, 12:48 PM

It's always up to you and your time! But it'll be nice for members!

lsturbointeg · 11-09-2015, 02:17 PM

Quote:

Originally Posted by mragarg

It's always up to you and your time! But it'll be nice for members!

Thanks! Anything to help fellow members and hopefully they do the as as well

mragarg · 11-09-2015, 02:46 PM

Quote:

Originally Posted by lsturbointeg

Quote:

Originally Posted by mragarg

It's always up to you and your time! But it'll be nice for members!

Thanks! Anything to help fellow members and hopefully they do the as as well

This was very well made! Thank you!

MARKPRIOR · 11-10-2015, 02:17 AM

Very good guide

Vapiano · 03-12-2016, 01:46 PM

Nice write up, thanks. I will be installing my Beltronics STi-R+ when I can find some time to do it. I don't think 3M tape is going to work well holding the radar receiver to the bumper housing. I'd rather bolt it on.

lsturbointeg · 03-12-2016, 03:32 PM

As long as you clean the surface very well the 3m tape will hold very well! But if you can find away to bolt it on than kudos!

F10FanDan · 03-18-2016, 01:59 AM

If you were to install the M bumper back on, does it require the same method / bolts?

10-22-2015, 01:49 AM	#1
lsturbointeg Lieutenant General 9151 Rep 14,522 Posts Drives: 2011 535i Jet Black Join Date: Aug 2014 Location: Asian lost in OH iTrader: (0)	DIY: front bumper removal non m w/ pictures! 9 pages i went through and nothing with pictures! anybody have a link or did i just miss it? appreciate it guys! Okay...decided to post a DIY with pictures for those of you who are contemplating doing it yourself. 1) "Pop the hood" as how our fallen brother Paul Walker said to Vin Diesel 2) locate the rubber seal just above where the bumper and Hood meet 3) Peel the rubber gasket completey off CAREFULLY 4) there are 4 of these pull/push type fasteners u need to remove. I used a small pliers but just pull the pin up like so and wiggle it as both parts should come up 5) next there are 4 T30 torx bolts that need to be removed 6) now next step would be to turn your wheel in depending on which side you're working first 7) there are 3 screws you will need to remove inside the fender wheel using a 5/16" socket Bottom Middle Top right where the fender/bumper meet 8) here is where you'll need to go next...where the fender meets the front bumper. Doesn't matter which side you do first as they're both the same. As you can see I popped the fender liner open a bit 9) there are 2 more 5/16" screws to remove...the one all the way inside takes a bit or work as you really have to pull the fender well out and in a bit to get to. Up can see the screw next to my thumb The 2nd one you can see way up inside 10) had to google these next images but next remove lower grills. Pull them with your fingers as they are just snapped in like so 11) remove the 2 5/16" screws 12) disconnect the fog lights from the harness by simply squeezing the tabs and pulling out. I put the fog lights in my trunk so I don't scratch the lens 13) last thing is to remove the 8 5/16" bolts underneath 14) now all you have to do carefully is wiggle the bumper off and that's it. Install is the same. Hope that helps everyone as I searched all over the internet for DIY with pictures and came up empty __________________ ~F90Conversion~21"3Piece Forged AvantGardeWheels~KWV1Coilovers~CQUENCE slotted/drilled rotors~GoodridgeStainlesslines~MeisterschaftQuadEx haust~Akrapovic 4"tips~VRSF DP~VRSF CP~TurboSmart BOV~K&N filter~CarbonFiberExteriorComponents~GladenAlphaCo mponents~MatchUp7BMW~Punch P300-12T~ Follow me on Instagram: lsturbointeg Last edited by lsturbointeg; 11-09-2015 at 02:14 PM..
	Appreciate 4 delje08152.00 F10ARNOLD82.00 Tweet Quote

11-09-2015, 12:36 PM	#2
mragarg Second Lieutenant 64 Rep 263 Posts Drives: 2014 BMW 550i Join Date: Nov 2015 Location: Atlanta iTrader: (0)	Did you ever find it? __________________ 2007 Lexus ES350 2007 Lexus RX350 2005 Lexus ES330 1972 Mercedes Benz 280 SEL 2014 BMW 550i
	Appreciate 0 Quote

11-09-2015, 12:48 PM	#4
mragarg Second Lieutenant 64 Rep 263 Posts Drives: 2014 BMW 550i Join Date: Nov 2015 Location: Atlanta iTrader: (0)	It's always up to you and your time! But it'll be nice for members! __________________ 2007 Lexus ES350 2007 Lexus RX350 2005 Lexus ES330 1972 Mercedes Benz 280 SEL 2014 BMW 550i
	Appreciate 1 Quote

11-10-2015, 02:17 AM	#7
MARKPRIOR Captain 156 Rep 659 Posts Drives: 2017 M6 GC Join Date: Apr 2015 Location: Newcastle iTrader: (0)	Very good guide __________________ Current: 2017 M6 Gran Coupe Previous:2014 640D GC 383BHP + 733NM, F10 2010 530d 520i (2000), E36 comact 318i, E46 M3, E46 318Ci, X5, Non BMW: 5x Skyline / GTRs, 5x Supras, 2x Nissan 200sx s14a, lots of other stuff
	Appreciate 1 Quote

03-12-2016, 01:46 PM	#8
Vapiano Private 13 Rep 91 Posts Drives: 2014 550ix AW- 2007 Dinan M5 Join Date: Dec 2012 Location: Maryland iTrader: (0)	Nice write up, thanks. I will be installing my Beltronics STi-R+ when I can find some time to do it. I don't think 3M tape is going to work well holding the radar receiver to the bumper housing. I'd rather bolt it on. __________________ 2007 M5, 6 speed, Silver Gray Metallic, Full Black Merino Leather, Brushed Ti Trim, HUD, Active M Comfort Seats/Heated & Cooled, Navi, Premium Sound, HK L7, Active Steering/Suspension, PDC, Rear & Side Sunshades, Adaptive Bi-Xenon, Voice Command, Custom S/W, Passport 9500ci w/jammers, Dinan High Flow Air Mass Meter/Intakes, CF Front Strut Brace, S1 Suspension & Free Flow Exhaust, Evolve S2 Tune
	Appreciate 1 Quote

03-12-2016, 03:32 PM	#9
lsturbointeg Lieutenant General 9151 Rep 14,522 Posts Drives: 2011 535i Jet Black Join Date: Aug 2014 Location: Asian lost in OH iTrader: (0)	As long as you clean the surface very well the 3m tape will hold very well! But if you can find away to bolt it on than kudos! __________________ ~F90Conversion~21"3Piece Forged AvantGardeWheels~KWV1Coilovers~CQUENCE slotted/drilled rotors~GoodridgeStainlesslines~MeisterschaftQuadEx haust~Akrapovic 4"tips~VRSF DP~VRSF CP~TurboSmart BOV~K&N filter~CarbonFiberExteriorComponents~GladenAlphaCo mponents~MatchUp7BMW~Punch P300-12T~ Follow me on Instagram: lsturbointeg
	Appreciate 0 Quote

03-18-2016, 01:59 AM	#10
F10FanDan New Member 2 Rep 15 Posts Drives: Imperial Blue Join Date: Mar 2016 Location: Niagara Falls, ON iTrader: (0)	If you were to install the M bumper back on, does it require the same method / bolts?
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search