BMW F10 Coding DIY (and other Fxx models)

bunnypv · 08-20-2023, 02:45 PM

Quote:

Originally Posted by Shoezy

Anyone here experienced with esys willing to help me code an F10 headlight? Replaced the entire headlight but still getting the codes from the old one that got water in it.

hey, i had a headlight unit with water in on my F10, but my control module did not get faulty. Maybe i can help, PM me.

bunnypv · 08-20-2023, 02:48 PM

Quote:

Originally Posted by shawnsheridan

PM sent.

I mostly might need your help, going through the posts, looks like you are the go to guy

TIA

shawnsheridan · 08-20-2023, 04:01 PM

Quote:

Originally Posted by bunnypv

after tirelessly looking all over the internet and hours of youtube videos, i was finally able to get the e-sys up and running, but, now i need help. i have replaced by gear shift module, and previously, the fuel pump module was also replaced. i am unable to code them to my vehicle, although it works fine, i get an error in ista, someone PLEASE help!!!

Quote:

Originally Posted by bunnypv

I mostly might need your help, going through the posts, looks like you are the go to guy

TIA

Did you inject CAFD into GWS and EKPM and VO Code them? Bear in mind, GWS in some cars has no CAFD as it is not a codeable ECU.

bunnypv · 08-21-2023, 08:28 AM

Quote:

Originally Posted by shawnsheridan

Did you inject CAFD into GWS and EKPM and VO Code them? Bear in mind, GWS in some cars has no CAFD as it is not a codeable ECU.

I haven't coded it yet, i have attached the ISTA errors and also what i see in ESYS for my car, please have a look and advise

PS Sent in PDF as i can share a larger file

shawnsheridan · 08-21-2023, 09:30 AM

Quote:

Originally Posted by bunnypv

I haven't coded it yet, i have attached the ISTA errors and also what i see in ESYS for my car, please have a look and advise

PS Sent in PDF as i can share a larger file

Try and Inject CAFD and VO Code both ECU:

Connect => Read FA (VO) => Activate FA (VO) => Read (ECU) => Left-Click on desired ECU => Click on "Detect CAF for SWE" => Select the CAFD from latest I-Level shown (bottom one) => Select OK => Right-Click on ECU (the ECU itself not the underlying CAFD) => Select CODE.

bunnypv · 08-21-2023, 10:31 AM

Quote:

Originally Posted by shawnsheridan

Try and Inject CAFD and VO Code both ECU:

Connect => Read FA (VO) => Activate FA (VO) => Read (ECU) => Left-Click on desired ECU => Click on "Detect CAF for SWE" => Select the CAFD from latest I-Level shown (bottom one) => Select OK => Right-Click on ECU (the ECU itself not the underlying CAFD) => Select CODE.

so i followed the procedure, and this is what i get:

Transaktions-Report: Aktion: Codieren

Abort!
Error in SVT. [C398]
duplicate ECU entry for diag address 23 [165]

shawnsheridan · 08-21-2023, 10:45 AM

Quote:

Originally Posted by bunnypv

so i followed the procedure, and this is what i get:

Transaktions-Report: Aktion: Codieren

Abort!
Error in SVT. [C398]
duplicate ECU entry for diag address 23 [165]

This is Fuel Pump, and your .pdf shows both EKPM (Target) and EKPM2 (Actual).

Did you replace EKPM2 with an older EKPM?

bunnypv · 08-21-2023, 10:55 AM

Quote:

Originally Posted by shawnsheridan

This is Fuel Pump, and your .pdf shows both EKPM (Target) and EKPM2 (Actual).

Did you replace EKPM2 with an older EKPM?

No, the fuel pump was replaced with a new unit. So, i ran the coding another time and it went through, but still no code, attached pics

bunnypv · 08-21-2023, 10:59 AM

Quote:

Originally Posted by shawnsheridan

This is Fuel Pump, and your .pdf shows both EKPM (Target) and EKPM2 (Actual).

Did you replace EKPM2 with an older EKPM?

i think that's gone back to normal, but i was still unable to code EKPM and GSW

shawnsheridan · 08-21-2023, 11:02 AM

Quote:

Originally Posted by bunnypv

No, the fuel pump was replaced with a new unit. So, i ran the coding another time and it went through, but still no code, attached pics

Quote:

Originally Posted by bunnypv

i think that's gone back to normal, but i was still unable to code EKPM and GSW

Picture shows nothing. What happened when you injected CAFD and VO Coded them?

bunnypv · 08-21-2023, 11:12 AM

Quote:

Originally Posted by shawnsheridan

Picture shows nothing. What happened when you injected CAFD and VO Coded them?

post th instructions, the coding went through, but it still highlights in my e-sys. in ista, programming date still shows 99.99.99
attached PDF, it actually has 3 images, 2nd and 3rd are the same, just expanded the modules in the 3rd pic

shawnsheridan · 08-21-2023, 11:47 AM

Quote:

Originally Posted by bunnypv

post th instructions, the coding went through, but it still highlights in my e-sys. in ista, programming date still shows 99.99.99
attached PDF, it actually has 3 images, 2nd and 3rd are the same, just expanded the modules in the 3rd pic

Programming Date is clearly not working, and Programming is not same as Coding anyway. Looks good. No more to do.

bunnypv · 08-21-2023, 12:46 PM

Quote:

Originally Posted by shawnsheridan

Programming Date is clearly not working, and Programming is not same as Coding anyway. Looks good. No more to do.

that was of great help, thank you Shawn

shawnsheridan · 08-21-2023, 12:46 PM

Quote:

Originally Posted by bunnypv

that was of great help, thank you Shawn

riske23 · 09-08-2023, 11:20 AM

Can somebody help me to code my new TMS module on my f10 2013? Adaptive headlight works, but angel eyes doesn't works. I have E sys, but when I open some CAFD in names of folders stays only one dot, and I m not sure what I should to open.
Sorry on my English, I hope you will understend me �� Thanks in advance

shawnsheridan · 09-08-2023, 11:57 AM

Quote:

Originally Posted by riske23

Can somebody help me to code my new TMS module on my f10 2013? Adaptive headlight works, but angel eyes doesn't works. I have E sys, but when I open some CAFD in names of folders stays only one dot, and I m not sure what I should to open.
Sorry on my English, I hope you will understend me �� Thanks in advance

You need CAFD Mapping solution, like BimmerUtility. PM sent.

Scorpion55 · 09-16-2023, 12:53 AM

2012 bmw 535( years ago I had a 13 x6 and was able to run a app on iPhone with it usb plugged into console so I could stream a huge variety of music . Now I can’t seem to find all or something?

Reino2002 · 09-20-2023, 11:57 AM

Hi! My F11 was on recall for factory update and after that the coding I have done was gone. I tried to code again and noticed that my ESYS was several years old and did not found all ecus.

May I have the link to the new version on ESYS to get the coding done?

shawnsheridan · 09-20-2023, 02:19 PM

Quote:

Originally Posted by Scorpion55

2012 bmw 535( years ago I had a 13 x6 and was able to run a app on iPhone with it usb plugged into console so I could stream a huge variety of music . Now I can’t seem to find all or something?

I have no idea on this. I don't use iPhone.

shawnsheridan · 09-20-2023, 02:20 PM

Quote:

Originally Posted by Reino2002

Hi! My F11 was on recall for factory update and after that the coding I have done was gone. I tried to code again and noticed that my ESYS was several years old and did not found all ecus.

May I have the link to the new version on ESYS to get the coding done?

PM sent.

uakcay · 11-03-2023, 02:32 AM

Hello,
Is there a bimmercode coding list for f10 and g30. There is a lot of scattered and complex information everywhere. If you could help with this situation, I would greatly appreciate it. I use Bimmercode with vgate.

DementedF10 · 11-03-2023, 09:31 AM

Found this page while looking for info on some parts I replaced as well as a code i read in bimmerlink.

I replaced the shifter assembly and need to code it to the car as well as there is something on the steering column that pops up which I assume the previous owner replaced.

Lastly there is a code 801C20 Central Fault memory full that keeps popping up. Havent been able to clear this one at all.

Anyone able to share some knowledge and ista/e-sys, whatever it is I need. Thank you!

09-08-2023, 11:20 AM	#609
riske23 Registered 0 Rep 3 Posts Drives: BMW 525 XD Join Date: Sep 2023 Location: Serbia iTrader: (0)	Can somebody help me to code my new TMS module on my f10 2013? Adaptive headlight works, but angel eyes doesn't works. I have E sys, but when I open some CAFD in names of folders stays only one dot, and I m not sure what I should to open. Sorry on my English, I hope you will understend me �� Thanks in advance
	Appreciate 0 Quote

09-16-2023, 12:53 AM	#611
Scorpion55 Registered 0 Rep 3 Posts Drives: Bmw 2012 535 Join Date: Sep 2023 Location: Kansas city iTrader: (0) Garage List 2012 bmw 535i f10 [0.00] 2012 bmw 535i [0.00]	2012 bmw 535( years ago I had a 13 x6 and was able to run a app on iPhone with it usb plugged into console so I could stream a huge variety of music . Now I can’t seem to find all or something?
	Appreciate 0 Quote

09-20-2023, 11:57 AM	#612
Reino2002 Registered 0 Rep 1 Posts Drives: F10 Join Date: Sep 2023 Location: Finland iTrader: (0)	Hi! My F11 was on recall for factory update and after that the coding I have done was gone. I tried to code again and noticed that my ESYS was several years old and did not found all ecus. May I have the link to the new version on ESYS to get the coding done?
	Appreciate 0 Quote

11-03-2023, 02:32 AM	#615
uakcay New Member 0 Rep 8 Posts Drives: Bmw Join Date: Oct 2023 Location: baku iTrader: (0)	Hello, Is there a bimmercode coding list for f10 and g30. There is a lot of scattered and complex information everywhere. If you could help with this situation, I would greatly appreciate it. I use Bimmercode with vgate.
	Appreciate 0 Quote

11-03-2023, 09:31 AM	#616
DementedF10 Private First Class 168 Rep 116 Posts Drives: 2012 BMW 535ix Join Date: Dec 2022 Location: Ohio iTrader: (0)	Found this page while looking for info on some parts I replaced as well as a code i read in bimmerlink. I replaced the shifter assembly and need to code it to the car as well as there is something on the steering column that pops up which I assume the previous owner replaced. Lastly there is a code 801C20 Central Fault memory full that keeps popping up. Havent been able to clear this one at all. Anyone able to share some knowledge and ista/e-sys, whatever it is I need. Thank you!
	Appreciate 0 Quote