2010 2011 BMW 5 Series Forum F10
BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read
 

2010 2011 BMW 5 Series Forum F10 BIMMERPOST Universal Forums General Automotive (non-BMW) Talk + Photos/Videos DIY Dent/Rust Repair and Body Work
Post Reply
 
Thread Tools Search this Thread
      04-18-2018, 06:38 PM   #1
Matticus91
Brigadier General
Matticus91's Avatar
United_States
3470
Rep
3,722
Posts

Drives: 2013 135i
Join Date: Aug 2015
Location: Washington DC

iTrader: (6)

Talking DIY Dent/Rust Repair and Body Work

I'm not going to go into too much detail since I followed ChrisFix's instructions to a T along with the instructions for the paint I used. I'll link the video at the bottom of the thread and go over the basics.

Wanted to share to show this is possible and doable for a newbie with zero bodywork skill.

This is my wife's Mazda 3. Damage was caused by a rouge poll in a parking garage, she never stood a chance

Goal of the project was to prevent rust and try to get the car looking a little better without blowing, at the very least, her $500 deductible at a shop. I also wanted to do it in a way that wouldn't impair a professional from fixing this "properly" in the future, if we became interested in that.

Stuff used:
  • Color matched paint set from AutomotiveTouchup.com
  • Automotive Green Tape
  • Glass reinforced bondo
  • Bondo body filler
  • Filler Primer
  • Paint-safe cartridge mask
  • Shitload of gloves
  • Rubbing Alcohol
  • Plastic sheeting from Home Depot
  • Wet sandpaper (160, 320, 600, 1000, 1500 grits)
  • Dry Sandpaper (50 & 80)
  • Sanding block
  • Cordless drill with a wire brush
  • A deadblow hammer
  • Heat gun
  • Tools to take off back bumper and tail light

Total cost for everything expendable: $80 (not including cost of reusable tools)

Here's what I started out with - you can tell how far in it was pushed and how much creasing there was in these pictures:
Mazda3DentFix
Mazda3DentFix
Mazda3DentFix

First step was using the wire brush to get down to bare metal. Then using the heat gun and hammer with a long screwdriver I did my best to pull the dents and reshape the metal in a way that it wouldn't pop back or move when touched.
Mazda3DentFix

After that, it was time for the fiberglass body filler to get enough material to have a strong backer and fill the dents. Then after sanding down some of the glass I did the first layer of bondo, followed by sanding. Then more bondo. Then more sanding. Then more bondo again, followed by additional sanding, and then sanding some more. Finally, sanding again.... and then a little more. All to try and get the shape of the body back and correct the lines that were gone or creased.
Mazda3DentFix
Mazda3DentFix
Mazda3DentFix
Mazda3DentFix
Mazda3DentFix
Mazda3DentFix

Eventually, when I decided I needed to stop sanding or I would be at risk of becoming part of the car, I decided to start the painting process. WHICH MEANT... more sanding. This time with a higher grit in prep for the paint. A couple coats later and I was wet sanding the primer to prep for paint.
Mazda3DentFix
Mazda3DentFix

The paint came in 4 stages:
  1. Filler primer
  2. Ground coat (primary color)
  3. Midcoat (pearl/flake)
  4. Top coat (clearcoat)

This next picture is after just one decent coat of groundcoat. After a couple more coats I added the flake, and then sat around for half an hour as it dried.
Mazda3DentFix
Mazda3DentFix
Mazda3DentFix

Finally I applied the clearcoat and let the car sit overnight before peeling away all the protective plastic and tape to reveal my work. If you look close or were told the car was damaged you'd be able to pick out some inconsistencies in the body filler, but for $80 and having never done anything like this before I'm extremely happy with the results. The paint is fixed, the body is 90% better, the seams are sealed and painted, and there's no chance of rust now.

I still need to wet sand and polish the clearcoat once it fully hardens to bring out the flake and glossiness. The paint matches pretty decently despite the bumper being a bit faded.

The car is filthy still since I have to wait to wash it but it looks pretty good even before polishing!

Mazda3DentFix by Matt Steele, on Flickr
Mazda3DentFix by Matt Steele, on Flickr

Here's ChrisFix's video on how to fix rust that I used as a guideline for this project, I don't think I would have even considered attempting this if I hadn't watched his video first.

__________________
"Tobias" 2013 135i ///M-Sport 6MT • Pure Stage 1 • XDI 35 HPFP • 404whp/440wtq
Appreciate 3
zx10guy5139.00
grzes32.50
      04-18-2018, 06:45 PM   #2
lennyf
Private First Class
lennyf's Avatar
162
Rep
138
Posts

Drives: 2017 BMW M240i
Join Date: Aug 2016
Location: SoCal

iTrader: (0)

Looks like an Ed China job.
Appreciate 0
      04-18-2018, 07:00 PM   #3
Matticus91
Brigadier General
Matticus91's Avatar
United_States
3470
Rep
3,722
Posts

Drives: 2013 135i
Join Date: Aug 2015
Location: Washington DC

iTrader: (6)

Quote:
Originally Posted by lennyf View Post
Looks like an Ed China job.
*Edd China and I'll take it lol
__________________
"Tobias" 2013 135i ///M-Sport 6MT • Pure Stage 1 • XDI 35 HPFP • 404whp/440wtq
Appreciate 0
      04-19-2018, 07:37 AM   #4
Never_Enough
Banned
United_States
2202
Rep
2,476
Posts

Drives: Satan's Chariot 2.0
Join Date: Sep 2013
Location: PA

iTrader: (6)

Garage List
Good work
Appreciate 0
      04-19-2018, 08:38 AM   #5
are0lies
Banned
United_States
4181
Rep
1,867
Posts

Drives: 2011 M3 E93
Join Date: Jun 2016
Location: Riverside

iTrader: (0)

Not bad, from the photos.
Appreciate 0
      04-19-2018, 08:58 AM   #6
omasou
Colonel
omasou's Avatar
United_States
2080
Rep
2,999
Posts

Drives: BMWs
Join Date: Apr 2016
Location: US

iTrader: (4)

Garage List
2023 BMW S1000RR  [0.50]
2022 BMW F900XR  [3.00]
2022 BMW X6 40i  [0.50]
2020 BMW M2C  [9.50]
nice job!
Appreciate 0
      04-19-2018, 09:43 AM   #7
3798j
Lieutenant Colonel
3798j's Avatar
11167
Rep
1,775
Posts

Drives: E86 3.0si
Join Date: Oct 2011
Location: Susquehanna Valley

iTrader: (0)

Garage List
'08 Z4 3.0SI  [8.50]
'66 Triumph TR4A  [0.00]
'85 Corvette  [0.00]
'64 Corvette  [0.00]
'68 Triumph GT6  [0.00]
'55 Ford F100  [0.00]
'19 VW Golf "R ...  [0.00]
I'm impressed. Nice job.
Appreciate 0
      04-19-2018, 11:31 AM   #8
EDWYER
Yoda of mods
EDWYER's Avatar
1668
Rep
3,003
Posts

Drives: X5 RWD
Join Date: Feb 2018
Location: NC

iTrader: (40)

Garage List
2015 X5 RWD  [0.00]
2016 BMW M2  [10.00]
Fantastic job.
Appreciate 0
      04-27-2018, 03:47 PM   #9
8k4
First Lieutenant
163
Rep
369
Posts

Drives: E92
Join Date: Nov 2015
Location: Earth

iTrader: (0)

Not bad, color is slightly off. What paint did you use?
Appreciate 0
      04-27-2018, 04:01 PM   #10
King Rudi
Lieutenant Colonel
King Rudi's Avatar
13152
Rep
1,965
Posts

Drives: Meat Suit
Join Date: Sep 2017
Location: Planet Earth

iTrader: (0)

Well done!
Appreciate 0
      04-27-2018, 04:09 PM   #11
BayE30
Lieutenant Colonel
United_States
1341
Rep
1,881
Posts

Drives: 2011.75 E90 M3 ZCP
Join Date: Jul 2014
Location: San Francisco

iTrader: (5)

i work in autobody industry, this is not how its done FYI. But whatever works for you...i guess.
Appreciate 0
      04-27-2018, 11:09 PM   #12
Matticus91
Brigadier General
Matticus91's Avatar
United_States
3470
Rep
3,722
Posts

Drives: 2013 135i
Join Date: Aug 2015
Location: Washington DC

iTrader: (6)

Quote:
Originally Posted by SFCM3 View Post
i work in autobody industry, this is not how its done FYI. But whatever works for you...i guess.
What would you do for something like this? Cut away damage/weld in new section from donor?
__________________
"Tobias" 2013 135i ///M-Sport 6MT • Pure Stage 1 • XDI 35 HPFP • 404whp/440wtq
Appreciate 0
      04-28-2018, 09:55 AM   #13
Bt12
Captain
391
Rep
960
Posts

Drives: 2018 X5,2018 m2, 2018 x1
Join Date: Sep 2017
Location: Bicoastal

iTrader: (0)

Good job. I use to enjoy this stuff when I was younger. Now I’m just lazy.
Appreciate 0
      05-07-2018, 04:59 PM   #14
dzvero
Lieutenant Colonel
528
Rep
1,514
Posts

Drives: 2015 M$4 F82
Join Date: Dec 2015
Location: CA

iTrader: (2)

nice job , what brand bondo/filler did you use?
Appreciate 0
      05-07-2018, 05:22 PM   #15
BayE30
Lieutenant Colonel
United_States
1341
Rep
1,881
Posts

Drives: 2011.75 E90 M3 ZCP
Join Date: Jul 2014
Location: San Francisco

iTrader: (5)

Quote:
Originally Posted by Matticus91 View Post
What would you do for something like this? Cut away damage/weld in new section from donor?
Pull/hammer straight, apply less than 3mm of filler to smooth out the metal repair, seal and paint. We never ever use any fiber filler for repairs, it will crack and fail.
Appreciate 0
      05-07-2018, 05:45 PM   #16
IllSic_Design
Colonel
IllSic_Design's Avatar
United_States
2123
Rep
2,758
Posts

Drives: 09 E92 335i
Join Date: Jun 2016
Location: Northern California

iTrader: (1)

Quote:
Originally Posted by dzvero View Post
nice job , what brand bondo/filler did you use?
Evercoat is a good brand. Please don't buy "Bondo" brand
Appreciate 0
      05-07-2018, 06:03 PM   #17
dzvero
Lieutenant Colonel
528
Rep
1,514
Posts

Drives: 2015 M$4 F82
Join Date: Dec 2015
Location: CA

iTrader: (2)

Quote:
Originally Posted by IllSic_Design View Post
Evercoat is a good brand. Please don't buy "Bondo" brand
Thanks, I have same experience with "bondo" - drys fast and uneven surface in thin layers. Its almost impossible to do good job with it
Appreciate 0
Post Reply

Bookmarks

Tags
body, dent, fix, repair, rust

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 06:05 AM.




5post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST