[asian]

Originally Posted by Thetiko

Wow Clean Wagon, Congratulations Bro

Thanks boss!

[asian]

After the first failed attempt due to Covid and then a few months long as it had to go via sea.. it has arrived!!!!! I actually originally chose this style but then when it didnt come I tried for the one with the 2 fins in the middle (most common style I think) but they sent me my original choice

New motor should be here this week too so hopefully have the car back up an running in a few weeks ready for moddddddds

I hope fitment is okay. Where do all the screws/fixings go??

[Ickdeep]

You'll have to take the rear bumper off and line up the tabs from the diffuser into the bumper. Then use the screws to hold the tabs in. Kind of a pain but definitely worth it.

[ramman434]

Diffuser looks great. planning to go that route when I finally do the exhaust

[asian]

Originally Posted by Ickdeep

You'll have to take the rear bumper off and line up the tabs from the diffuser into the bumper. Then use the screws to hold the tabs in. Kind of a pain but definitely worth it.

Thanks bro! Hmm that seems like a really dodgy way to secure it haha you would think there was a better way to do it. I guess it's the cheapest way and gets the job done..

Fk, cant wait!!

[asian]

Originally Posted by ramman434

Diffuser looks great. planning to go that route when I finally do the exhaust

What exhaust you planning? Good to do all at the same time because now I have to adjust the tips to align and suit the new diffuser. Zzz

[ramman434]

Originally Posted by asian

What exhaust you planning? Good to do all at the same time because now I have to adjust the tips to align and suit the new diffuser. Zzz

I'm leaning towards the Megan Supremo quad tip axle-back. I'll basically get a downpipe, and then have an exhaust shop weld in either an X or H pipe to the Megan.
Only thing that bugs me is I'm going from a 4" DP to a 2.5" pipe on the Megan. I wish it was a bit bigger, but it's not like I'm boost crazy (completely stock) and have a lot of back pressure to get rid of.

[lsturbointeg]

Originally Posted by Ickdeep

You'll have to take the rear bumper off and line up the tabs from the diffuser into the bumper. Then use the screws to hold the tabs in. Kind of a pain but definitely worth it.

same thing. had to take my bumper off to do this method with the screws. the screws in place will keep the tabs from popping out of the slot. too bad you didn't get the diffuser that had the 2 fins. oh well, this one look pretty clean tho

Originally Posted by ramman434

I'm leaning towards the Megan Supremo quad tip axle-back. I'll basically get a downpipe, and then have an exhaust shop weld in either an X or H pipe to the Megan.
Only thing that bugs me is I'm going from a 4" DP to a 2.5" pipe on the Megan. I wish it was a bit bigger, but it's not like I'm boost crazy (completely stock) and have a lot of back pressure to get rid of.

once you put those Megan Supremos it'll sound nice. but once you install the dp the exhaust note will definitely change in a very good way

[asian]

Yeah I was kinda bummed it was without fins but also want the cleaner look and not so aggressive. I don't know..only time will tell lol

[lsturbointeg]

Originally Posted by asian

Yeah I was kinda bummed it was without fins but also want the cleaner look and not so aggressive. I don't know..only time will tell lol

bro! there is the inner piece you can buy that has smaller fins
https://emnotek.com/products/autotec...saAtp2EALw_wcB

[top ramen]

@asian - instead of drilling and using screws to hold your diffuser to the bumper what I used to hold my aftermarket diffuser was bumper retainer clips. They are Hyundai/Kia bumper retainer clip that I found at advance auto. They just slide right over the diffuser tabs.

Here's the link to the retainer clips. I think there are 3 clips to a pack.
https://shop.advanceautoparts.com/p/...30d/11910672-P

[asian]

Originally Posted by top ramen

@asian - instead of drilling and using screws to hold your diffuser to the bumper what I used to hold my aftermarket diffuser was bumper retainer clips. They are Hyundai/Kia bumper retainer clip that I found at advance auto. They just slide right over the diffuser tabs.

Here's the link to the retainer clips. I think there are 3 clips to a pack.
https://shop.advanceautoparts.com/p/...30d/11910672-P

Interesting!! How do they work? I dont understand how that would secure on. Do you put the tabs though the bumper holes and then jam the clips teeth on the end? Kinda like a paper clip? Got any pics of your install?

Originally Posted by lsturbointeg

bro! there is the inner piece you can buy that has smaller fins
https://emnotek.com/products/autotec...saAtp2EALw_wcB

Oh thanks! That's nice! But way too expensive haha might as well buy another diffuser

[top ramen]

Originally Posted by asian

Interesting!! How do they work? I dont understand how that would secure on. Do you put the tabs though the bumper holes and then jam the clips teeth on the end? Kinda like a paper clip? Got any pics of your install?

Yes, push the diffuser tab through the bumper and insert the retainer clip on the the tabs. By pushing the retainer clip on the tab all the way against the bumper the retainer clip teeth will grab onto the tab and hold it in place. Sorry I don't have photos.

[asian]

Originally Posted by top ramen

Yes, push the diffuser tab through the bumper and insert the retainer clip on the the tabs. By pushing the retainer clip on the tab all the way against the bumper the retainer clip teeth will grab onto the tab and hold it in place. Sorry I don't have photos.

Thanks bro! Now... I wonder if I can get any locally in Aus.

[top ramen]

Originally Posted by asian

Thanks bro! Now... I wonder if I can get any locally in Aus.

Try google search "hyundau/kai bumper retainer clip" that's how I found where they were selling locally.

[asian]

Originally Posted by top ramen

Try google search "hyundau/kai bumper retainer clip" that's how I found where they were selling locally.

Found them! They are called razor blade clips. Sounds suicidal

https://www.repco.com.au/en/parts-service/vehicle-body-parts/body-panels/champion-razor-blade-clips-pp84/p/A9124992

[asian]

1 seized engine and 3 months later, she's back!

3 changes happened today:
- blackvue dashcams (father's day gift)
- big knob (bigger is better apparently)
- msport steering wheel (finally!)

Next week the diffuser goes on too. Heck to the yes! Eggcite!

[BurrNinja]

Loving the look of the wagon! That thing is looking doper by the mod!

[NYC535iowner]

Originally Posted by f10_will

Check out mine

wow the car is sexxxy all around. love the brake setup and the simple/ clean look of the car..

[NYC535iowner]

in regards the F11 wagon. I will love to rock that car out here in the USA....

[asian]

Thanks gents!

Bloody diffuser didn't fit Workshop said miles off and not workable.

China crappp #racisttomyownkind

[Unspec]

How you liking those paddle shifters? I have the same ones but in black aluminum and honestly starting to want to go back to stock. It's a lot more mushy when you click them down and they aren't quite as stout feeling as the stock paddles.