[tonytony99]

Hey friends, been reading a lot and still have no answers

About to order some Niche 20x10.5 and 20x9 +35 offset on front and rear.
I was going to order 255/35/20 Nitto 555G2 for front and 285/30/20 for rear.

Few questions, dropping the car on coilovers, will this setup rub?

Also, will 255 and 285 be stretched a little, do I need a 265/35 and 295/30 instead for it to be flush?

Im sure these would fit just fine at stock height I am just worried about fitment after dropping the car?


Any feedback or suggestions please!!

[tonytony99]

Originally Posted by M335

20x10.5 +42 with 305 on the back on stock M suspension 👍🏻

What size wheel and tire are on the front?

[Eadames]

Hello Gentlemen,

Want to install different wheels on my 5 series.

Front: 8.5x20 ET38
Rear: 10x20 ET51

Will these wheels fit my car? And what size tires should I put on?

[bamberjim]

255/35/20 front and 285/30/20 for rear. genuine M5 wheels no rubbing on Eibach pro sport springs

[Eddiek550]

Can anyone provide some insight on what tires to go with?

I want a thicker side wall. I had 245/35/20 and 285/30/20 Super Sports and ended up blowing out each front (separate occasions but both at night - hate NJ roads). Being that I am AWD, i calculated that i can run a few different sizes but the question is will it rub - i am not currently lowered as i want to save getting springs until i figure out tires (i.e. if tires fill the gap on their own then i won't get springs)

Wheels are HRE FF04 20x9 ET25 front and 20x10 ET40 rear.

Can I run the following without rubbing?

255/40/20 (28" height)
295/35/20 (28.1" height)

I know brand and model tire matters as well and to be honest, i was not a fan of the super sports. Sport 4s is what i am looking at currently, but would like advice on other brands/models.

Main concerns are to avoid spinning on launch (in awd) and avoid spinning on 40/60 rolls (in RWD via xDelete) while also resisting potholes more than before (if possible).

Any and all suggestions appreciated!

[slev1111n]

Tnx for the info guys! It really helped my friend. we argued about it for a long time and in the end he agreed with what is said here

[Taylorguy74]

Originally Posted by M335

20x10.5 +42 with 305 on the back on stock M suspension ����

How far does that stick out? Is the wheel flush, or protruding outside of the lip of the fender? Do you have any pics you could share? I'm considering a similar ET, just with a 285 or even 275 tire.

[Dif-one]

Hate to hijack threads but currently running’s 20x9 245/35 ET35 fronts and 20x10.5 285/30 ET42 rears. I feel like I have room to be a more aggressive with the fitment. I’m lowered on H&R springs. How aggressive can I get front and rear? I see ET25 fronts but rears? ET 35?

[Bitchn5ive]

Originally Posted by Bitchn5ive

Can I throw one out here:

I have 20x9 et 30 and 20x10 et 38 on a 550i xdrive lowered on ACS springs.

Currently on 245/35 and 275/30 w/o issues but want to go a bit wider.

How do you think 255/35 and 295/30's work out?

Thanks in advance!

Just following up to confirm this works. No rubbing so far and I don't think it will. It is tight though.

Continental Extreme Contact 255/35/20 Front and 295/30/20 Rear with 20 x 9 et30 and 20 x 10 et38 respectively. Some pics:

Jacked up from opposite side to check clearance...



Sitting normal...

[RalphgF10]

Originally Posted by JayBimmer83

Love the Niche wheels. I have the same ones but all black. I got the 20x9 square set.

Is that 20x9 +35 cause I want the same size but the Niche Gamma