[janneh123]

Thanks Shawn.
I plan to flash my NBT HU since the bluotooth support are not so good, is it best to flash to the lastest version or are there limitations in this that make the internet by bluetooth tethering not work ?

[shawnsheridan]

Originally Posted by janneh123

Thanks Shawn.
I plan to flash my NBT HU since the bluotooth support are not so good, is it best to flash to the lastest version or are there limitations in this that make the internet by bluetooth tethering not work ?

I am not aware of any limitation.

[janneh123]

Ok good, Thanks Shawn !
I started the flash process but during TAl calculation I got a varning
-3 Tal lines have been set to "NotExecutable" during TAL calculation [C384]
And after this a new pop up massage
-1 WARN events during TAL generation [C383]
Any idea what the problem is ?

[shawnsheridan]

Originally Posted by janneh123

Ok good, Thanks Shawn !
I started the flash process but during TAl calculation I got a varning
-3 Tal lines have been set to "NotExecutable" during TAL calculation [C384]
And after this a new pop up massage
-1 WARN events during TAL generation [C383]
Any idea what the problem is ?

Why is it a problem? Is Flash not running or aborting prematurely?

[janneh123]

I did not dear to start the flash due to this warnings, is it ok to start the flash?

[shawnsheridan]

Originally Posted by janneh123

I did not dear to start the flash due to this warnings, is it ok to start the flash?

Yes, start it.

[Mr_Mario]

Hi Shawn,

Got 2014 F10 530d and looking to get some things enabled. Ordered cable on Amazon and now looking for latest software and guides. Also, is there any difference if it's UK car?
Thanks in advance.

[shawnsheridan]

Originally Posted by Mr_Mario

Hi Shawn,

Got 2014 F10 530d and looking to get some things enabled. Ordered cable on Amazon and now looking for latest software and guides. Also, is there any difference if it's UK car?
Thanks in advance.

No difference. PM sent.

[silk_cut555]

Hello, I'm new here too. Could I also get a copy of the cheatsheet for an F10 please. I have the cable and some software but not sure if its the correct.
Any help would be appreciated.

Thank you

[shawnsheridan]

Originally Posted by silk_cut555

Hello, I'm new here too. Could I also get a copy of the cheatsheet for an F10 please. I have the cable and some software but not sure if its the correct.
Any help would be appreciated.

Thank you

PM sent.

[silk_cut555]

Thank you very much Shawn.

[Slaider]

Hi there!
I have 520d Bimmer 2012 F11. madeup ENET cable, installed INSTA-D INSTA-P and E-sys plus have a 10A charger.
Have a few problems:
Need to determine accu state (afraid of 30% life, it`s didn`t change from the very beginning)
Also need to check AGR state
About coding:
Tell me where to look - I changed the bumper to M5 (without fogs) - respectively, they must be turned off, a permanent error. Prompt where to find.

The rear camera is also of interest in motion;
lowering the limiting speed of the dead zones (up to 25 km)
see \ change the time the headlight washer is switched on
check the ability to assign a button (that belongs to front fogs) to another function
activate the Internet and all related functions (CIC native, wide monitor, not NBT )

Will be very thankfull for any help

[Slaider]

Hello!))
Updating....
I found some features, and want to share
About rear camera in motion:
PDC 3009 D_SCHWELLE_2 FF 0A max distance in meters to disable rear camera view - Change to Werte = FF
PDC 3009 V_SCHWELLE_2 FF 0F max speed to disable rear camera view - Change to Werte = FF

test it - have only one bug - if do all this - rear camera didn`t switch off by itself when you put reverse, and then forward. I`ll do it manually, button))

Dead lane \dead spot system

ICM 3000 Daten, F8 Hc2_i_CPar_Aktiv_v_low 30 50


Works. But I did 30km/h, when it was 25 - have errors, so I don`t recommend to do it lower than that
===================
All other things are still in search...
Looking for help...Anyone?

[Almaretto]

Originally Posted by Slaider

test it - have only one bug - if do all this - rear camera didn`t switch off by itself when you put reverse, and then forward. I`ll do it manually, button))

That is not a bug. You are coding for it to stay on.

[MARKPRIOR]

Hi all

have been coding my F06 with success, however for the life of me i cannot get the indicators in the HUD

KOMBI => 3008 => HUD_PIA_BLINKER => aktiv
KOMBI => 3000 => BLINKER_HUD_ENABLE => aktiv
HU_NBT => 3001 => HUD_TURNSIGNAL => aktiv

is whats noted in the cheat sheet however i noticed min is held under

DKOMBI xxxxxxxxxxxxxxxx

[Almaretto]

Originally Posted by MARKPRIOR

DKOMBO xxxxxxxxxxxxxxxx

No HUD blinkers for DKOMBI.

[MARKPRIOR]

Originally Posted by Almaretto

No HUD blinkers for DKOMBI.

yeah thats the one, i also have the digital cluster which after some reading may be the issue ?

[Almaretto]

Originally Posted by MARKPRIOR

yeah thats the one, i also have the digital cluster which after some reading may be the issue ?

No question.

[MARKPRIOR]

Originally Posted by Almaretto

No question.

[MARKPRIOR]

next coding question

Reverse also illuminates door LEDs, couldnt find this for the F10 code list, (im actually coding my F06) just using the f10 sheet

[shawnsheridan]

Originally Posted by MARKPRIOR

next coding question

Reverse also illuminates door LEDs, couldnt find this for the F10 code list, (im actually coding my F06) just using the f10 sheet

Not possible in F1x (FRM based) car.

[andykap]

Can I get a copy of the code sheet?

Thanks in advance.