[barni320]

Hi,

- Today I've tried to code in F11 new steering column after replacement. Power steering was working normally,
however I didn't have any cafd file in EPS module, so I searched for swe, selected the bottom one and coded then. Coding was unsuccessful, I get an error and power steering stopped working. I've never have any errors with coding. What can make the errors, old psdzdata or something different?

- I have one more question about headlights modules. I didn't see modules connected with headlights, only FRM, but I have to code module of left headlight as it doesn't work after replacement. Which ones are xenon headlights modules? Picture attached

[shawnsheridan]

PM me car VIN and Donor EPS VIN.

[barni320]

Originally Posted by shawnsheridan

PM me car VIN and Donor EPS VIN.

PM send

[barni320]

shawnsheridan I've tried to flash EPS as per your instruction. Unfortunately I had some errors.

Pic 1


Firstly I've flashed ZGW without any problems and ZGW disappeared from the TAL list. After that I've tried to do the same with EPS [30].

Pic 2. Before ZGW flash


Pic 3. After ZGW flash


As I understand to flash EPS I had to check: tl_13, tl_21, tl_51 theirs PreRequisites.

1)TalLine_13 -> tl_18 & tl_6
2)Talline_21 -> tl_18 & tl_6
3)Talline_51 -> none

tl_18 & tl_6 are parts of DSC2 and they don't have any PreRequisites.

Summarizing I've checked all available boxes of DSC2 and EPS to flash and I've get an error as attached.

[shawnsheridan]

Originally Posted by barni320

shawnsheridan I've tried to flash EPS as per your instruction. Unfortunately I had some errors.

FA Null is VIN issue. You must select "Vin from FA", then hit Read FA, and then Execute TAL.

Do exactly as follows:

1) Read FA
2) Select Read VIN our of FA & "Read VIN"
3) Then do all of the ECU Selects - blflash...
4) Do the Check Software
5) Then select the "Read VIN out of FA" which greys out the "Enter VIN"
6) Then do the Start...

[barni320]

Originally Posted by shawnsheridan

FA Null is VIN issue. You must select "Vin from FA", then hit Read FA, and then Execute TAL.

Do exactly as follows:

1) Read FA
2) Select Read VIN our of FA & "Read VIN"
3) Then do all of the ECU Selects - blflash...
4) Do the Check Software
5) Then select the "Read VIN out of FA" which greys out the "Enter VIN"
6) Then do the Start...

Thank you shawnsheridan , EPS works 💪.

What about xenons? Do they have any separate modules to code/flash? One headlight doesn't work correctly. DRL works , low and high beams don't.

I've attached the list of my modules.

[shawnsheridan]

Originally Posted by barni320

Thank you shawnsheridan , EPS works 💪.

What about xenons? Do they have any separate modules to code/flash? One headlight doesn't work correctly. DRL works , low and high beams don't.

I've attached the list of my modules.

No, you have only FRM Module for Xenon lights.

[barni320]

Ok, I've flashed the FRM, selected new cafd and coded, no errors but it didn't help.

I suspect also a broken xenon converter itself. Awaiting for new part already.

Do xenons require any coding or they should work p&p after module replacement if the car was originally xenon fitted?

[shawnsheridan]

Originally Posted by barni320

Ok, I've flashed the FRM, selected new cafd and coded, no errors but it didn't help.

I suspect also a broken xenon converter itself. Awaiting for new part already.

Do xenons require any coding or they should work p&p after module replacement if the car was originally xenon fitted?

If FRM is good, then just install new Light module.

[barni320]

Ok, I will check if new converter helps.

[barni320]

Problem solved. Xenon converter was broken.

[shawnsheridan]

Originally Posted by barni320

Problem solved. Xenon converter was broken.